logocree     Logo-Intematix       

Controller and converters

Controllers are intelligent devices, that allow several play of light or LED light-dimming. Converters are devices that convert a kind of signal in another.

EN1649

PROGRAMMABLE DALI DRIVER 48V

DALI controller, DALI DT6 IEC 62386 compatible. 1 output.

EN1658 DALINAMIC

 DALINAMIC

DALI controller, DALI DT8 IEC 62386 compatible. 2 outputs (tunable white).

EN1658 PUSHNAMIC

TUNABLE WHITE AND DIM TO WARM CONTROLLER

Controller DALI/DMX

EN0995

  • ON/OFF and dimming through DALI or DMX protocol.
  • DMX chanel setting through Dip Switch

Converter DALI/DMX and DMX/DALI

EN1056

  • Conversion of DALI signal in DMX one and viceversa.
  • DMX chanel setting throught Dip Switch.

Controller DMX

EN0757

  • ON/OFF and dimming through DMX protocol.
  • DMX chanel setting through Dip Switch.

Mini controller DMX/RDM

EN1162

  • ON/OFF and dimming through DMX and RDM protocol.

EN1418

DMX signal repeater

En1418 permits to extend the range of DMX signal in order to connect up to 31 devices more than the maximum quantity set by the line and more than the maximum cables lenght.
These additional devices will be connected to the line generated by the repeater.

EN1576

OPtO-INSUlATED REPEATER, DALI COMPATIBlE

Repeater to opto-insulate the DALI input signal protocol.

Sequencer

EN0723

  • Selection of colors, colors cycle and desired speed.
  • Settings are automatically stored and resumed at power on.
  • Control from external buttons (not included) available radio remote control version and/or IR remote control and receiver version.
  • Possibility to connect more sequencers and synchronize them.

Mini sequencer

EN0800

  • Selection of colors, colors cycle and desired speed.
  • Settings are automatically stored and resumed at power on.
  • Control from extarnal buttons (not included).
  • It is not possible to connect more Mini Sequencers.

TUNABLE WHITE DIMMER

EN0723

  • Setting of the desired white color temperature
  • Setting of the desired brightness level.
  • Controller with soft start: when it is powered on/off, the output is gradually activated/deactivated.
  • Brightness and white CCT are automatically stored and resumed at power on.
  • Control from external buttons (not included) - radio remote control version available.

Touch control units

EN0832

The Touch control units are devices based on Touchpad technology and allows you to easily control the brightness of white LEDs, to select the color and brightness of RGB LEDs and to set cycles of color mixing. It can be installed on 4-modules mounting frames of the most popular brands.

01 TOUCH COLOR VERSION

  • 3 RGB + 1 white output.
  • Selection of colors, brightness level, color cycle speed.
  • Possibility the control from two external buttons (not included).

02 TOUCH LIGHT VERSION

  • 2 output for warm white and cold white.
  • Mix of desideredwhite temperature and brightness, 4 preset programs.
  • Possibility the coontrol from two external buttons (not included).

Touch control units DMX

EN0871

The Touch control units are devices based on Touchpad technology and allows you to easily control the brightness of white LEDs, to select the color and brightness of RGB LEDs and to set cycles of color mixing. It can be installed on 4-modules mounting frames of the most popular brands.

TOUCH COLOR DMX VERSION

  • 3 RGB + 1 white outputs.
  • Selection of colors, brightness level, colors cycle speed with DMX signal.
  • Possibility the control from two external buttons (not included).
  • Possibility to connect more touch units to control a complex system from different points.

EN1282

EN1282 Board for battery detach

EN1282 board has been designed to be integrated in battery-powered products. Specifically, at a certain voltage (set as standard at 10.5V - customizable value), it detaches the battery preserving it and allowing further recharges.

Dimmer board for power supply 0-10V

EN1259

EN1259 dimmer board is the ideal solution for systems with power supply 0-10V. Connected directly to the power supply 0-10V, it makes possible to dim the light source from the switch in use, without structural interventions or cables. For more information, also about dimming mode, see the Datasheet.

 

Powering up the board, the output will lead to the set value.
Turning off and on three times in succession the card will go into programming
mode and will start to vary the output from maximum to minimum and vice versa.
Upon reaching the desired brightness power cycle the power to save the current
state, that state will be proposed to the next switch.

Dimmer board for DALI power supply

EN1310

EN1310 dimmer board is the ideal solution for systems with power supply DALI. Connected directly to the power supply DALI, it makes possible to dim the light source from the switch in use, without structural interventions or cables. For more information, also about dimming mode, see the Datasheet.

Powering up the board, the output will lead to the set value.
Turning off and on three times in succession the card will go into programming
mode and will start to vary the output from maximum to minimum and vice versa.
Upon reaching the desired brightness power cycle the power to save the current
state, that state will be proposed to the next switch.